DeBug Husky All-terrain Beach Wheelchair

DeBug Husky All-terrain Beach Wheelchair

We build the DeBug Husky Wheelchair with the highest quality materials, keeping in mind the comfort and positioning of the rider.

Usage & Safety

DeBug Beach Wheelchair should not be used during inclement weather, dangerous surf, rough ocean currents, rip tides and any other poor conditions. !

We recommended the chair be used only when a lifeguard is present. Safety comes first! Users must always be accompanied by a responsible, able-bodied adult.

Using your DeBug Beach Wheelchair

Always maintain control of your DeBug while in use. When the DeBug is not in use, the safety brakes must be engaged to prevent the chair from moving unexpectedly. The DeBug was built to not tip over, even when used over uneven surfaces. However, to ensure safety and prevent injury, the user must always wear the seatbelt while using the DeBug. This is imperative to the user’s safety.

Do not use the components of the DeBug Beach Wheelchair for any purpose other than what is intended. Do not have more than one person using the DeBug.

General Maintenance

It’s so easy to maintain your DeBug Husky Beach Wheelchair Just follow these simple instructions, and you will be able to enjoy your chair year after year.

Rinse the chair off with clean water to remove any sand or debris after each use. The sling material is removable and machine washable.

Check tire pressure before each use

If at any time you need to lubricate any part of the chair, DO NOT USE WD-40, as it will attract dirt and sand, causing possible damage to the wheel bearing/ bushings. We recommend P.T.F.E Dry Lube, all wearing components. This dry film is a superior lubricant and repels debris and water, marine and performance parts stores likely stock this locally.

Assembly / Disassembly of DeBug Husky WheelChair:

• 1/4”- 20tp X 1-1/4” SS Backrest Bolts - 2 each
• Legrest Adjustment Knobs - 2 each
• 18 SS Main Axle Pin - 2 each
• 1/4 - 20 X 2,25” SS Hex Bolts - 2 each
• 1” SS Main Axle Flat Washer - 2 each

Assembling Instructions:

• 1. Slide On The Leg Support Sling, And Install The Two 5/16”-18 Adjustment Knobs
• 2. Slide On The Foot Plate, And Tighten The Leg Rest Adjustment Knobs
• 3. Install The Mid Axle, Tighten The Two Attaching 1/4”-20 Bolts
• 4. To Install The Backrest, Slide The Backrest Down On The Chair Frame And Attach Using The Two 1/4”-20 Bolts
• 5. The Rear Suspension May Be Attached By Inserting The Rear Suspension Tension Bolt. This Bolt Should Be Tight During Use

Disassembling Instructions

1. Loosen The Leg Length Adjustment Knobs And Slide Out The Footplate
2. Slide Off The Leg Support Sling By Removing The Two 5/16”-18 Adjustment Knobs
3. To Remove The Mid Axle, Loosen The Two Attaching 1/4”-20 Bolts
4. To Remove The Backrest, Remove The Two Attaching 1/4”-20 Bolts And Slide Up On The Backrest
5. The Rear Suspension May Be Detached By Removing The Rear Suspension Tension Bolt. This Bolt Should Be Tight During Use

Optional Third 49 Centimeter Wheel For Husky Beach:

The diagram above is a bottom view showing the main axle spacer and washer configuration with the optional third wheel shown. the arrows starting from top two bottom or pointing at 

1. 1Six one inch stainless steel washers
2. Two vertical one inch spacers
3. Four horizontal axle spacers

General Specifications:

• The DeBug Beach Wheelchair frame is constructed using #316L Stainless Steel tubing, which is a higher grade than standard “#304 marine grade” stainless. Weight capacity 400 pounds.
• The rear Caster wheels rotate 360 degrees. The wheel hubs are made from poly-nylon material to eliminate saltwater corrosion.
• The DeBug has a footrest for proper foot support.
• Wheel Lock –Adjustable tension wheel brake can be actuated independently on each side.